Kite_Spares__Parts_and

Stopper Clip / C Clip
Hard plastic C-shaped clips which snap onto the spar next to other frame fittings to hold them firmly in the right position. Can be glued in place.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Flexifoil Grommet
Pliable rubber grommet as used on Flexifoil power kite spars. The grommet is fitted onto the spar before the end cap is glued on, and keeps the flying line in position at the end of the spar.

Fits Flexifoil Spar (4.0mm)

Price: £0.29 (Including VAT at 17.5%)

Quantity:

Vinyl End Cap
Soft, pliable cap which fits over the end of a spar to prevent wear and damage to the kite fabric when inserted into a pocket or the nose of a kite.
Sourced from various suppliers depending upon price and availability, therefore colours may vary.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Flexifoil end caps
Firm rubber end cap as used on Flexifoil power kite spars. This cap is glued onto the tip of the spar. The flying line is attached between the grommet and the cap
Price: £0.29 (Including VAT at 17.5%)

Quantity:

Nock / Split End Cap
Assorted rigid caps with end slots. These fittings are glued to the end of a spar, along which the sail is tensioned with cord or bungee at the split end.
These nocks are sourced from various suppliers (Exel, HQ, Dura), therefore the shape may vary
slightly from the image shown.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

FSD Cap (Flat Nock)
Rigid plastic spar caps with flat closed end and either a hole or side slot for sail tension cords. The smooth end prevents lines from catching and helps prevent the wing tip from digging into the ground.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Air~Crafts Stand-off Sail Grabber
Rigid stand-off connector which is glued on to the end of the stand-off, then hooked through a small reinforced hole in the trailing edge of the kite.

Fits 2.5mm stand-off
Price: £0.25 (Including VAT at 17.5%)

Quantity:

Dura Stand-off Sail Grabber
Rigid stand-off connector which is glued on to the end of the stand-off then pushed through a small reinforced hole in the trailing edge of the kite

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

HQ Stand-off Sail Grabber
Soft plastic clip which folds over the edge of the sail and fits flush against the fabric. The stand-off fits into the cap and is usually glued in place.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Air~Crafts Stand-off Spar Grabber
Rigid plastic connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar is glued into the hole in the base and the top clamps on and off the lower spreader.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Dura Stand-off Spar Grabber
Rigid plastic connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar is glued into the hole in the base and the top clamps on and off the lower spreader

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Air~Crafts Flexi Stand-off Spar Grabber
Firm, flexible connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar fits into the hole in the base and the spreader is inserted into the larger hole.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

HQ Stand-off Connector
Soft, pliable connector which joins two spars together at a 90 degree angle to form a T shape. These connectors will accommodate smaller stand-offs which have been fitted with an end cap.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

APA Stand-off Connector
Soft, pliable connector which joins two spars together at a 90 degree angle to form a T shape. All have a 5.5mm end hole to accommodate a 3mm stand-off with a vinyl end cap.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Straight Leading Edge Connector
Flexible rubber connector for joining two spars together at a 90 degree angle to form the shape of a T.
Sourced from various suppliers, therefore the shape may vary slightly from the image shown.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Centre T Connector
Rigid plastic connector for joining three spars together at 90 degree angles to form the shape of a T.

Price: £0.69 (Including VAT at 17.5%)

Quantity:

TAPA Angled Leading Edge Connector
Soft rubber connector for joining two spars together at a 45 degree angle.
Mixed size combinations.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

APA Angled Leading Edge Connector
Soft rubber connector for joining two spars together at a 45 degree angle.
Mixed size combinations

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

HQ Angled Leading Edge Connector
Soft rubber connector for joining two spars together at a 45 degree angle.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

TW Angled Leading Edge Connector
Soft rubber connector for joining two spars together at a 45 degree angle.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Air~Crafts Angled Leading Edge Connector
Firm, flexible connector for joining two spars together at a 45 degree angle.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Centre Cross Connector
Rigid plastic connector for joining three spars together at 90 degree angles to form a cross.
Sourced from various suppliers, therefore the shape may vary slightly from the image shown.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

FSD Machined Centre T STD
Machined fitting to join two or three spars together at
90 degrees to form a cross. Includes aluminium ferrule for fitting the spreader spar into.
Fitting requires Allen key.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

FSD Machined Centre T (G-Force and Skinny)
Machined fitting to join two or three spars together at
90 degrees to form a cross. Includes machined plastic locating sleeve and internal carbon ferrule.
Fitting requires Allen key.
Fits G-Force & Skinny spars.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

FSD Machined Centre T (no ferrule)
Machined fitting to join two or three spars together at
90 degrees to form a cross. Fitting requires Allen key
Supplied without ferrule
6.0mm vertical hole & 8.0mm horizontal hole.

Price: £1.99 (Including VAT at 17.5%)

Quantity:

Central Joint
Rigid connector used to join two spars together to form the shape of a cross
Price: £0.49 (Including VAT at 17.5%)

Quantity:

Dihedral Connector
Rigid connector for joining three spars together at an angle to form an angled cross (keel).
Normally used on Eddy/Diamonds

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Rigid Nose Fitting
Rigid and slightly angled connector used to join three spars together to form the nose of a kite. This type of fitting eliminates the need for a stitched webbing nose.
4.0mm spine and 4.8mm spreaders
Price: £1.99 (Including VAT at 17.5%)

Quantity:

Flexible Nose Fitting
Flexible, flat connector used to join three spars together to form the nose of a kite. This type of fitting eliminates the need for a stitched webbing nose.
4.0mm spine and 4.0mm spreaders
Price: £1.99 (Including VAT at 17.5%)

Quantity:

Flexible Air~Crafts Nose Fitting
Flexible connector used to join three spars together to form the nose of a kite. This type of fitting eliminates the need for a stitched webbing nose.

Priced by size (price includes VAT at 17.5%)

Size

Quantity:

Rubber Band
Soft and stretchy bands which are ideal for tensioning sails when used with a wing tip nock.
Price: £0.09 (Including VAT at 17.5%)

Quantity:

Rubber/Vinyl O Ring
Flexible O-rings which can be twisted around two intersecting spars to hold them together in the
shape of a cross.
17.0mm o.d. x 11.0mm i.d.
Price: £0.20 (Including VAT at 17.5%)

Quantity:

Moulded Triangular Ring
Rigid moulded polypropylene triangular ring ideal for using with webbing for straps.
40mm along flat edge (outside)
28mm along flat edge (inside)

Price: £0.20 (Including VAT at 17.5%)

Quantity:

Buckle Adjuster
Rigid moulded buckle fitting designed for adjusting the length of straps.
Fits 25mm webbing strap.
30mm external length
25mm internal length

Price: £0.15 (Including VAT at 17.5%)

Quantity:

Oblong Loop / Strap Holder
Rigid moulded buckle fitting designed for adjusting the length of straps.
Fits 25mm webbing strap.
30mm external length
25mm internal length

Price: £0.15 (Including VAT at 17.5%)

Quantity:

Plastic Snap Hook
Rigid moulded swivel hook for shoulder strap attachments
Fits 38mm webbing strap.

Price: £0.40 (Including VAT at 17.5%)

Quantity:

Cord Lock Toggle
These black nylon locks feature an internal spring and lock on to cords up to 5mm diameter, preventing the cord from retracting into garment seams or enclosures.
Ideal for outdoor applications.

Price: £0.20 (Including VAT at 17.5%)

Quantity:

Yo-Yo stoppers- each

Price: £0.90 (Including VAT at 17.5%)

size:

Quantity: